⚡New V200Pro PowerScan Circuit Tester Electrical Diagnostic Power Probe AVOmeter

Description: VDIAGTOOL V200 Pro Upgraded set : 3 in 1 Automotive Power Circuit Probe Tester Breaker Finder with 30 Pin 👋Dual combination mode helps you to check complex automotive circuits faster. Mode1️⃣: Monitoring of circuit data values. Normal component measurements do not exceed a reasonable range. Mode2️⃣: Circuit problem localization. Accurate indication of fault points through audible alarms to assist in repairs. VDIAGTOOL V200 Pro Upgraded set : 3 in 1 Automotive Power Circuit Probe Tester Breaker Finder with 30 Pin VDIAGTOOL V200 Pro Upgraded set : 3 in 1 Automotive Power Circuit Probe Tester Breaker Finder with 30 Pin 💯（🥳🥳 🥳 2024 NEW Upgraded Pro Set🥳 🥳 🥳 ）💯 >>>Highly effective assistant tool - “V200 Pro”👋Dual combination mode helps you to check complex automotive circuits faster.Mode1️⃣: Monitoring of circuit data values. Normal component measurements do not exceed a reasonable range. Mode2️⃣: Circuit problem localization. Accurate indication of fault points through audible alarms to assist in repairs. ⚡ Mode1 - [4 cyclic operating modes]➊ DC Voltage Measurement: reads DC voltage with 0.1 volt resolution.➋ AC Voltage Measurement: reads the maximum voltage, minimum voltage, frequency and duty cycle.➌ Resistance Measurement: Reads the resistance between the tip and auxiliary ground lead.➍ Diode Measurement: Read the resistance value displayed by the diode. If the resistance value displayed is outside of a reasonable range, the diode is damaged and needs to be replaced.⚡ Mode 2 - [Accurately locate the fault ]❗ ❗ Note❗ ❗ (Mode II-circuit breaker tester is powered by 1 Piece 9V Battery! ) If the fuse keeps blowing, resulting in a short-circuit in the car's wiring; you can combine it with the extracted DTC report, and use the V210-Wire Finder to quickly determine the location of the fault and find out the root cause of the electrical problem.you will be able to use the breaker finder which can easily locate the circuit breaker point, open connections, broken wires, current leaks with tone change, even trace wire/cable without damaging the insulation. This circuit breaker finder tool works on all kinds of vehicle circuit issues such as those found in car, SUV, mini van, truck, tractor, boat & RV, with voltages between 6 and 42 volt DC. ⚡ Upgraded Additional 30 Pin Probe Kit- [more accurate connections and measurements]Multi-Angle Design: The probe set contains 3 different angles (90°, 135°, Straight), making it easier to inspect in narrow or hard-to-reach areas. Material & Durability: The probes made of stainless steel ensure durability and stability for long term use. Fine Tip: With a tip diameter of only 0.07 mm, the probe can accurately reach tiny connector or sensor points, making it suitable for fine work. High Voltage Testing Capability: The ability to test circuits up to 30 volts, including connectors, fuel injectors and automotive sensors, increases the range of applicability of the probes. 5 Crocodile Clips: 5 crocodile clips are included in the kit, the end of each clip can be connected to a 4mm male banana plug, providing more connection options and convenience. With a maximum opening of 15mm, the alligator clips are able to accommodate different sizes of connections. Colour differentiation: 5 different colours of crocodile clips, easy for users to quickly identify and differentiate them during the testing process, improving work efficiency. Safety Standard: Complies with CATII 300Vac/15A safety standard, ensuring safety when used in high voltage environments. About VDIAGTOOL"V200 Pro Upgrade Set"The V200Pro Upgrade Probe Kit is a set of professional automotive circuit inspection tools designed to meet diverse needs in different test environments. This backside probe lead set is suitable for automotive service technicians, electronic engineers, or any professional who needs to perform fine circuit testing. Whether you are performing routine testing or solving complex circuit problems, this kit provides the necessary support and convenience. >>>Product Features:👍[Component Activation Function] V200Pro power circuit tester tool generates activation signals by directly contacting the components through the power supply current, you can connect the components through the probes to determine whether the components are in good condition or not in the actual use, such as lamps, motors, windshield wipers, radiator fans, relays and so on. and also test various sensors, signal circuits to pinpoint the root cause to electrical issues when you have extracted DTCs from vehicle ECUs.⚡【Equipped 2 Head Lights & LCD Digital Screen】The electric test pen comes with a lighting function to support your testing needs in a low-light environment. At the same time, this V200 circuit light tester with highly clear LCD digital backlit display screen,clear&visible digital readouts for day and night. ⚡ 【OVERLOAD PROTECTION TO PROTECT CAR ELECTRONICS】 This automotive electrical tool comes with short circuit protection. Whenever it gets overloaded, it just gonna shut down and restart, which is a safe measure to protect the device and car electronics. Useful Tip: You can also use overload protection feature to test short circuit conveniently. NOTE: If you received defective unit or it malfunctions, please reach us via vdiagtool2 @ outl ook c om for hassle-free replacement any time!⚡ 【20FT EXTENSION CORD TO WORK ANYWHERE AROUND THE VEHICLE】 V200 Pro circuit tester automotive tool comes with 20 feet long cord plus 20 feet extension cord. Combining the feature that it can be powered by the cigarette lighter, and alligator clip for convenient ground connection, you can test electrical circuit system anywhere around the vehicle. No more worrying about short cord while testing electrical system!⚡ 【One-Step Solution for Auto Electrical System Test】V200 Pro meets the needs of 2 products at one time. Simply and quickly switch from the power circuit probe tester functional mode to the circuit breaker finder tool mode with one click. There is no need to get an extra tool to judge continuity of the cables/wire and diagnose the breaker point. This convenient and efficient circuit instrument is a great choice for DIYERS,electrician and technician.How to start using? 💐Step 1: Take out the adapter cable to link the device with the vehicle and provide electricity to start the preparation work. Description of the adapted cable: (one end of the double round end connects to the probe device and the other end has two large red and black clips) 💐 Step 2: Mode 1: the small clip attached to the probe device to contact the place to be detected, clamped after the start of the probe pillow to detect the internal, four detection modes can be switched at will. Sudden black screen or restart during use, indicating that the current location of the overload phenomenon: that is, what we call a short circuit. The device has an overload protection function, a short period of time will restart and can start testing again. Mode 2: Through the toggle switch, the screen of the probe device is turned off. Patrol equipment is enabled (need to add batteries), hold down the start button, the probe end of the line along the detection, when the rover appears to be a great sound reminder of the region is judged to be a circuit breaker. The device starts to use will be self-sound, can be adjusted by the right side of the rotary button.🔸🔹🔶Detail Display🔷🔸 🔹 Quick Self-testBuilt-in Light2 Charging Modes30 Pin SetQuick self test to make sure it is working properly before you start using it.Press the power switch forward to activate the tip with a positive voltage. The red LED lights up and display the battery voltage.Press the power switch backwards to activate the tip with a negative voltage, the green LED should light up and the display will read 0.0V.When you power up the circuit probe tester, the 2 led lights on top of it will automatically turn on.This could be a very useful feature when working in darker spaces such a fuse box under the steering wheel, for example, without having to use a flashlight.This power probe circuit can be powered by the car's battery or cigarette lighter, no extra battery or cable required. The V200 PRO upgrade kit includes a V200 Pro Automotive Circuit Tester and an additional 30 Pcs Probe Lead Kit. The 30 Pcs probe kit is used for wiring harness connectors, automotive sensors, fuel injectors and more. Includes back probe pins*15, Banana Plug to Alligator Clip Circuit Test Leads*5, Threading probes*5 Nickel-plated copper alligator clips *5. >>>WARNING:Applying voltage to some circuits at will damage the electronic components of the vehicle.Kindly use the vehicle manufacturer's schematics and diagnostic procedures when testing. >>>NOTE:When power up this probe tester kit, press the power switch first, then contact the tip with the component, the operation life of power switch will be extended. PaymentDelivery detailsTerms of salesAbout usContact usPayment1.We accept Credit cards、Debit card、Apple Pay、Google Pay、PayPal ect. payment. 2.Please contact us if you need to use another method to pay. 3.Payment should be made within 7 days after bidding ends. 4.Otherwise an Unpaid Item case will be opened to you. 5.We are not responsible for buyers’ local taxes. 6.Please include your special requests in eBay note if there is any. 7.We reserve the final right of sellingDelivery details Order will be shipped within 1-5 business day after payment confirmed. We have warehouse in US，HongKong，China warehouse. From our US warehouse via UPS or DHL eCommerce shipping Delivery time varies from 2 to 6 business days. From our Hong Kong warehouse via DHL or FedEx Ground Delivery time varies from 7 to 21 business days. From our China warehouse For US buyers, we use SpeedPAK (Delivery time is 8-15 business days) or express delivery(Delivery time is 7-21 business days) . For other countries' buyers, we use SpeedPAK or China Post or Hong Kong Post(Delivery time varies from 10 to 30 business days)or Express delivery(Delivery time is 7-21 business days). We will ship according to your eBay address. Please make sure it is correct and include phone number for delivery. If you do not receive your order in the estimated time, please contact us, we would do our best to serve you solve the problem. Please include your special requests in eBay note if there is any.Terms of sales We are authorize distributor, our all items are 100% original and Our devices have warranty, 12 months free repair for the devices. 3 months for the accessories. Please contact us firstly when you need warranty service. In case an item arrives faulty, please contact us in 30 days and keep it unused. We will instruct you on how to return and get refund or replacement. If after 30 days, or the item has been used, we have the right to decline your claim. Items should be returned on buyers' cost for repair or replacement.About us Who We Are? We are specialized dealer of On-Board Diagnostic tools and automotive electronics for more than 10 years. We are authorized first class distributor of VDIAGTOOL. What Do We Have? We have office and warehouse in CN and US to ensure fast shipment and after-sale service. Terms of tax: We are not responsible for buyer's local taxes, please consult your local Customs for tax details.Contact us Our customer-oriented service strives for positive feedbacks with all 5 star selling ratings. Please feel free to contact us via eBay message once you have any question before you giving us negative feedback or open case. We will reply in 24 business hours. Business time: GMT8 (9:00-18:00) from Monday to Friday.On Aug 27, 2024 at 02:44:56 PDT, seller added the following information:

Price: 119.99 USD

Location: Perth Amboy, New Jersey

End Time: 2024-09-27T09:25:43.000Z

Shipping Cost: 0 USD